0
Pure nickel anode bar in Ni200, Ni201, N4 and N6 for plating lines, straight grade with sulphur capped at 0.01%, annealed, 8-20 mm from stock and 3-300 mm to drawing, cut to the anode length the line runs.
Pure nickel bar for Indian buyers in Ni200, Ni201, N4 and N6, supplied annealed in round bar from 8 mm to 20 mm off the shelf and from 3 mm to 300 mm to drawing. Consignments are prepared with the mill test certificate and the customs paperwork for the consignee, and the invoice carries HSN 7505.11. Freight is quoted to the destination named on the enquiry.
Two things decide whether a nickel bar consignment clears without argument. The first is the grade: the certificate has to show the chemistry the purchase order named, and for pure nickel that means the carbon figure as well as the nickel content. The second is the paperwork: an invoice, a packing list, a bill of lading and a certificate of origin that agree with each other and with the HSN heading declared at the port.
Both are settled before the material is packed rather than after it sails. The grade is fixed at the melt and reported for the heat, and the commercial documents are drafted from the same order sheet, so the description on the invoice, the cases on the packing list and the analysis on the certificate describe one consignment. Buyers comparing grades across the pure nickel series can go from the UNS number to the trade name to the GB class without changing the material.
| Grades | Ni200 (UNS N02200) / Ni201 (UNS N02201) / N4 / N6 |
| Form | Round Bar / Rod (hexagonal and square per drawing) |
| Standard In-Stock Diameters | 8 mm / 10 mm / 12 mm / 20 mm |
| Other Diameters | 3-300 mm per drawing |
| Length | Per drawing (bar program supports up to 6000 mm) |
| Surface | Black / Peeled / Polished / Cold Drawn (Bright) |
| Temper | Annealed (standard) |
| HSN (India) | 7505.11, bars, rods and profiles of nickel, not alloyed |
| Export Documents | Mill test certificate (EN 10204 3.1), commercial invoice, packing list, bill of lading, certificate of origin |
| Density | 8.908 g/cm³ |
| Tensile Strength (min) | 462 MPa (annealed) |
| Yield Strength 0.2% (min) | 148 MPa (annealed) |
| Elongation (min) | 35% |
| Melting Point | 1435-1446°C |
Every grade in this range is produced under the pure nickel bar program.
HSN 7505.11 stated on the commercial invoice.
Mill test certificate (EN 10204 3.1) issued for the heat.
Invoice, packing list and bill of lading built from one order sheet.
8-20 mm round bar held in stock for short-notice shipments.
Case marks matched to the packing list for goods-in checking.
An enquiry that states the grade, the size, the length, the quantity and the destination port can be quoted from directly. Where the grade is written as a trade name such as Nickel 200 or Nickel 201, as a UNS number, or as a GB purity class, all three refer to material in this range, and the offer restates it in the form the purchase order will use. If the enquiry names a standard other than ASTM B160 or GB/T 4435, the equivalent grade is confirmed before the offer is issued so that no substitution happens later.
The mill test certificate (EN 10204 3.1) reports the heat chemistry and the mechanical results for the lot. It travels with a commercial invoice that names the grade, size, quantity, unit price, HSN heading and Incoterm; a packing list carrying case numbers with net and gross weight; a bill of lading issued for the agreed Incoterm; and a certificate of origin where the consignee or its bank requires one. Duty and GST are assessed by Indian customs at the time of import, and no rate is quoted from here.
Freight is quoted FOB, CFR or CIF against the destination named on the enquiry. Nhava Sheva (JNPT) and Mundra are the usual container gateways for metal imports into the country. The production window is separate from the sea leg: in-stock diameters leave in 3-7 days, standard production runs in 7-15 days, and diameters made to drawing ship in 15-30 days, with the sailing confirmed at the time of booking.
Bar is wrapped against moisture, packed in export wooden cases and marked with case numbers that match the packing list, so a consignee can reconcile the delivery against the documents before the cases are opened. The grade and the size are shown on each case, and cut lengths are packed to the length on the order rather than to a standard bundle.
| Grade | Ni+Co (min) | C (max) | Cu (max) | Fe (max) | Mn (max) | Si (max) | S (max) |
|---|---|---|---|---|---|---|---|
| N4 | 99.9% | 0.01% | 0.015% | 0.04% | 0.002% | 0.03% | 0.001% |
| N6 | 99.5% | 0.10% | 0.10% | 0.10% | 0.05% | 0.10% | 0.005% |
| Ni200 (UNS N02200) | 99.2% | 0.15% | 0.25% | 0.40% | 0.35% | 0.35% | 0.01% |
| Ni201 (UNS N02201) | 99.0% | 0.02% | 0.25% | 0.40% | 0.35% | 0.35% | 0.01% |
Annealed bar: tensile strength ≥462 MPa, 0.2% yield strength ≥148 MPa, elongation ≥35%, hardness 90-120 HB. Physical constants: density 8.908 g/cm³, melting point 1435-1446°C, electrical resistivity 0.096 μΩ·m, thermal conductivity (Ni200) 70.2 W/m·K, ferromagnetic below the Curie point of 358°C.
Each lot is measured at the diameter and the length stated on the order before it is packed, and the heat is analysed for composition at the melt. The certificate issued for the lot carries the same grade description that appears on the invoice, which is what allows a consignee to check the material against the documents rather than against a description given verbally.
Ni200/Ni201: ASTM B160 (Nickel Rod and Bar). N4/N6: GB/T 4435 (Nickel and Nickel Alloy Bars). Export documentation per EN 10204 3.1.
Material data references ASTM B160 and GB/T 4435; HSN 7505.11 follows the Indian customs tariff heading for non-alloyed nickel bar; corrosion and application guidance references the Nickel Institute and the ASM Specialty Handbook: Nickel, Cobalt, and Their Alloys; batch composition is verified against mill test certificates and in-house inspection records.
Bar is supplied in cut lengths or full bars, wrapped against moisture and packed in export wooden cases for the sea leg. The label carries the grade and the size supplied. In-stock diameters dispatch in 3-7 days, standard production in 7-15 days, and diameters produced to drawing in 15-30 days; the sea leg is quoted separately against the destination. Payment is by L/C, T/T, Western Union or MoneyGram.
Nickel-based material has been melted and processed at DZX Alloy's Changzhou, Jiangsu mill since 2002 under ISO 9001 and SGS quality systems, with exports to 60+ countries. For consignments to India, the document set is prepared around what the consignee's customs broker needs: the HSN heading on the invoice, case numbers on the packing list, and a certificate that describes the same grade the purchase order named.
Send the grade, size, quantity and destination port for a quote.
Q: What is the HSN code for pure nickel bar?
A: 7505.11, which covers bars, rods and profiles of nickel, not alloyed. The heading is shown on the commercial invoice, and duty and GST are assessed by Indian customs at the time of import.
Q: Which documents are issued for an Indian consignment?
A: A mill test certificate (EN 10204 3.1) with the heat chemistry and mechanical results, a commercial invoice naming the grade, size, quantity, HSN heading and Incoterm, a packing list with case numbers and weights, a bill of lading, and a certificate of origin where the consignee or its bank requires one.
Q: Which Incoterms can be quoted?
A: FOB, CFR or CIF against the destination named on the enquiry. The sailing date is confirmed at the time of booking.
Q: Which ports do shipments go to?
A: The port named on the enquiry. Nhava Sheva (JNPT) and Mundra are the usual container gateways for metal imports into India.
Q: What grades and sizes ship to India?
A: Ni200, Ni201, N4 and N6, annealed, in round bar from 8-20 mm out of stock, 3-300 mm to drawing, and hexagonal or square sections per drawing, in lengths up to 6000 mm.
Q: Can the material be supplied against a standard quoted on an Indian drawing?
A: State the standard and the grade on the enquiry. The equivalent grade is confirmed before the offer, and the material is produced and certified to ASTM B160 for Ni200 and Ni201 or GB/T 4435 for N4 and N6, with EN 10204 3.1 documents.
Q: Can samples be sent before an order?
A: Free 0.5 kg samples are available for N6 and Ni200 so a test part can be machined before the order is placed.
Q: What is the minimum order quantity?
A: MOQ is 10 kg.
Q: What is the delivery time?
A: In-stock diameters dispatch in 3-7 days, standard production in 7-15 days, and diameters produced to drawing in 15-30 days. The sea leg is quoted separately against the destination.
Q: What payment terms are accepted?
A: L/C, T/T, Western Union and MoneyGram.
E-mail: dzx@dlx-alloy.com
Mobile: +8619906119641
Tel: 0086-19906119641
WhatsApp: +86-19906119641
Add: NO.32 West Taihu Road, Xinbei District, Changzhou, Jiangsu
